|DodgeRam.info > TSB's > 18-037-05|
|Visit Geno's Garage
for Truck accessories.
Date: October 20, 2005
THIS BULLETIN SUPERSEDES SERVICE BULLETIN 18-020-02, DATED JUNE 24, 2002
WHICH SHOULD BE REMOVED FROM YOUR FILES. THIS IS A COMPLETE REVISION.
Models: 1994 - 2002 (BR/BE) Ram Pickup, 2002 - 2005 (DR/DH/D1) Ram Pickup
1992 - 1994 (AA) Spirit/Acclaim/Lebaron Sedan
1995 - 2003 (AB) Ram Van/Wagon
1992 - 1994 (AJ) Lebaron Coupe/Convertible
1995 - 2004 (AN) Dakota
1992 - 1995 (AS) Town & Country/Caravan/Voyager
1994 - 2002 (BR/BE) Ram Pickup
2004 - 2006 (CS) Pacifica
1998 - 2003 (DN) Durango
2002 - 2005 (DR/DH/D1) Ram Pickup
1995 - 2000 (FJ) Avenger/Sebring/Talon
1996 - 2000 (GS) Chrysler Voyager (International Markets)
1995 - 2000 (JA) Breeze/Cirrus/Stratus
2001 - 2006 (JR) Sebring Sedan/Stratus Sedan/Sebring Convertible
1996 - 2000 (JX) Sebring Convertible
2002 - 2005 (KJ) Liberty/Cherokee (International Markets)
1993 - 2003 (LH) Concorde/Intrepid/Vision/LHS/New Yorker/300M
1996 - 2000 (NS) Town & Country/Caravan/Voyager
1995 - 2005 (PL) Neon
2002 (PG) PT Cruiser (International Markets)
1997 - 2002 (PR) Prowler
2001 - 2005 (PT) PT Cruiser
2001 - 2006 (RG) Chrysler Voyager (International Markets)
2001 - 2006 (RS) Town & Country/Caravan/Voyager
1995 - 2002 (SR) Viper
2001 - 2005 (ST) Sebring Coupe/Stratus Coupe
1997 - 2006 (TJ) Wrangler
2001 - 2004 (WG) Grand Cherokee (International Markets)
1999 - 2004 (WJ) Grand Cherokee
1997 - 2001 (XJ) Cherokee
1993 - 1995 (YJ) Wrangler
2003 - 2006 (ZB) Viper
1995 - 1998 (ZG) Grand Cherokee (International Markets)
2004 - 2006 (ZH) Crossfire Coupe/Crossfire Roadster
1993 - 1998 (ZJ) Grand Cherokee/Grand Wagoneer
This Bulletin provides guidelines, to minimize flash reprogramming problems, and information
on recovery procedures for failed flash attempts.
NOTE: Many of the reasons a flash reprogramming procedure may not complete
documented in this service bulletin, but if you are constantly having issues
performing the flash reprogramming procedure using a specific DRBIII, it is
suggested you send the DRBIII in question to SPX/Miller Special Tools for
Occasionally a flash update procedure may not complete properly and/or the
equipment may lock up or become disconnected during the procedure. Flash Reprogramming
is a "CRITICAL PROCESS"; an error may result in a no-start/failed control module. Most
modules, encountering an interruption or failure while reprogramming, are recoverable; a
recoverable module is not covered under the provisions of the warranty.
This service bulletin covers items that may cause this condition, a process
to restart the flash
procedure, and miscellaneous information that will help prevent needless replacement of
Flash Reprogramming is only authorized by a specific SERVICE BULLETIN, or RECALL.
Review the entire Service Bulletin/Recall prior to performing a flash reprogramming
Often other parts may need to be serviced, replaced, or tested, prior to flash reprogramming,
and ARE REQUIRED as part of completing the Service Bulletin/Recall.
When flashing a Powertrain Control Module (PCM) or Transmission Control Module
there are other legal requirements with labeling issues that are included in those service
Other non-emission related modules, such as instrument clusters and Body Control
(BCMs) do not require labels.
FLASH REPROGRAMMING SEQUENCE OF EVENTS
The process of flash reprogramming is similar to flashing the BIOS on a Personal
Interruptions, voltage problems, and a variety of other outside interactions can potentially
interfere with the process. This document seeks to provide information to minimize problems
associated with vehicle control module flash reprogramming. The description that follows is for
most PCMs and some TCMs. Other modules use different initiation procedures.
The process starts by selecting an update from the TechCONNECT Client or ISIS
"loading" that update into the DRBIII. Once the flash reprogramming update is loaded into
the DRBIII, and before the flash reprogramming begins, the DRBIII verifies that the update
loaded from the TechCONNECT Client or ISIS is the proper update for the module. This is
done using part number supersedence. This verification occurs only if an update is required,
available (on the TechCONNECT Client or ISIS) and has been selected for programming.
SOFTWARE VERSIONS MUST BE CURRENT
Before attempting a flash reprogramming session using the TechCONNECT Client,
you have the most current DRBIII software installed.
To verify whether your DRBIII software is current, check the upper right-hand
corner of the
TechCONNECT Client screen for DRBIII Available Version, DRBIII Current Version.
Often, because of multiple DRBIIIs in the shop, not all will get updated on
a timely manner.
The installed DRBIII software version can generally be found at the bottom center of most
screens. Alternately the version can be checked by pressing 6, 2, 5 from the DRBIII Main
Menu and comparing it to what is available from a current TechCONNECT Client as described
If the TechCONNECT Client is current and the DRBIII is not, it may be due
to the fact that
the TechCONNECT Client does not force DRBIII updates for 9minor9 revisions. Changes and
new support are added to the Vehicle Flash application on 9minor9 revisions on a regular
basis. This is why your TechCONNECT Client and DRBIII must have the LATEST software
DO NOT PASS on the option for updating to a "minor" revision!
Major updates require the DRBIII to be updated prior to allowing any flash programming.
Note from Dave F: When the vehicle is "flashed" (new software loaded into the PCM or other locations on board the vehicle) the update procedure may not complete properly and/or the diagnostic equipment may "lock up" during the process. The TSB lists several possible problems and a process to reinitialize the flash procedure. Since you probably do not have a DRB III or the CD software or the cables, the very long procedure is not posted. If you need the complete bulletin, see your dealer for a copy. If you can't find a dealer that will provide a copy, contact me; I can email send you a pdf version.
Policy: Information Only
I would like to thank Bob Bergevin, Arthur Cantrall, Barry Drodge, David Lovell, Bill Maurits, and Steve for supplying the information for these bulletins. And a big thank you goes to Geno's Garage for making DodgeRam.info possible.
This page was edited on: May 3, 2004